Design, manufacture, install and commissioning E-House.
We have experience in several projects
In AGS PMC, we can design, manufacture, install and commissioning E-House for 11-36 kV substations, or E-House for Auxiliary Services, CCM, Pump Stations, etc…
We have experience in several projects that show our international skill in this field.
The new E-House 11kV substation’s switchgear is enclosed in a container all done upon request. AGS-PMC will provide a E-house control room that will be independent from the main E-House Subestation switchgear room.
All the features have been carefully established by calculating all structures and installations, and choosing the right designs and materials in accordance with the requirements of the customer.
Both containers (main and control room) will be placed on several pillars that will support the structure and will be accessible through two stairs that enable the entrance on either end of the switchgear.
Applicable legislation and references:
The installation of the 11kV substation has been designed according to International Standards and International
Standard Recommendation, especially IEC standard.
On this basis, all standard required to design the substation are included in the list shown below.
IEC 60085, Electrical insulation – Thermal evaluation and designation
IEC 60216-1, Electrical insulating materials – Properties of thermal endurance – Part 1: Ageing procedures and evaluation of test results
IEEE Std 80™-2000, IEEE Guide for Safety in AC Substation Grounding. Errata to IEEE Std 80™-2000, IEEE
Guide for Safety in AC Substation Grounding
IEEE Standards Interpretation for IEEE Std 80™-1986 IEEE Guide for Safety in AC Substation Grounding
IEEE Standards Interpretation for IEEE Std 80™-2000 IEEE Guide for Safety in AC Substation Grounding
IEEE Std 81™-2012, IEEE Guide For Measuring Earth Resistivity, Ground Impedance, And Earth Surface
Potentials Of a Ground System
IEEE Std 525™-2007, IEEE Guide for the Design and Installation of Cable Systems in Substations
IEEE Std 605™-2008, IEEE Guide for Design of substation Rigid-Bus Structures
Correction to IEEE Std 605™-1998, IEEE Guide for Design of substation Rigid-Bus Structures
IEEE Standards Interpretation for IEEE Std 605™-1998, IEEE Guide of substation Rigid-Bus Structures
IEEE Std 693™-2005, IEEE Recommended Practice for Seismic Design of Substations
IEEE Std 837™-2002, IEEE Standard for Qualifying Permanent Connections Used in Substation Grounding
IEEE Std 979™-2012, IEEE Guide for Substation Fire Protection (Pub 11/7/2012)
IEEE Std 998™-2012, IEEE Guide for Direct Lightning Stroke Shielding of Substations
IEEE Std 1031™-2011, IEEE Guide for the Functional Specification of Transmission Static Var Compensators
Errata to IEEE Std 1031™-2011, IEEE Guide for the Functional Specification of Transmission Static Var Compensators
IEEE Std 1127™-1998 (R2004), IEEE Guide for the Design, Construction, and Operation of Electric Power Substations for Community Acceptance and Environmental Compatibility
IEEE Std 1240™-2000 (R2012), IEEE Guide for the Evaluation of the Reliability of HVDC Converter Stations
IEEE Std 1246™-2011, IEEE Guide for Temporary Protective Grounding Systems Used in Substations
IEEE Std 1264™-1993 (R2009), IEEE Guide for Animal Deterrents for Electric Power Supply Substations
IEEE Std 1267™-1999 (R2005), IEEE Guide for Development of Specification for Turnkey Substation Projects
IEEE Std 1268™-2005, IEEE Guide for Safety in the Installation of Mobile Substation Equipment
IEEE Std 1379™-2000 (R2006), IEEE Recommended Practice for Data Communications Between Remote Terminal Units and Intelligent Electronic Devices in a Substation
IEEE Std 1402™-2000 (R2008), IEEE Guide for Electric Power Substation Physical and Electronic Security
IEEE Std 1416™-1998 (R2004), IEEE Recommended Practice for the Interface of New Gas-Insulated Equipment in Existing Gas-Insulated substations
IEEE Std 1585™-2002 (R2007), IEEE Guide for the Functional Specification of Medium Voltage (1 – 35 kV) Electronic Series Devices for Compensation of Voltage Fluctuations
IEEE Std 1613™-2009, IEEE Standard Environmental and Testing Requirements for Communications Networking Devices Installed in Electric Power Substations
IEEE Standards Interpretation for IEEE Std 1613™-2003 IEEE Standard Environmental and Testing Requirements for Communications Networking Devices in Electric Power Substations
IEEE Standards Interpretations for IEEE Std 1613™-2009 IEEE Standard Environmental and Testing Requirements for Communications Networking Devices Installed in Electrical Power Substations
IEEE Std 1615™-2007, IEEE Recommended Practice for Network Communication in Electric Power Substations
IEEE Std 1623™-2004 (R2010), IEEE Guide for the Functional Specification of Medium Voltage (1 kV…35 kV) Electronic Shunt Devices for Dynamic Voltage Compensation
IEEE Std 1646™-2004 IEEE Standard Communication Delivery Time Performance Requirements for Electric Power Substation Automation
IEEE Std 1686™-2007, IEEE Standard for Substation Intelligent Electronic Devices (IEDs) Cyber Security Capabilities
IEEE Std 1815™-2012, IEEE Standard for Electric Power Systems Communications – Distributed Network Protocol (DNP3)
IEEE Std C37.1™-2007, IEEE Standard for SCADA and Automation Systems
IEEE Std C37.2™-2008, IEEE Standard for Electrical Power System Device Function Numbers, Acronyms, and Contact Designations
IEEE Std C37.122™-2010, IEEE Standard for Gas-Insulated Substations
Errata to IEEE Std C37.122™-2010, IEEE Standard for Gas-Insulated Substations
IEEE Std C37.122.1™-1993 (R2008), IEEE Guide for Gas- Insulated Substations
IEEE Std C37.122.2™-2011 – IEEE Guide for the Application of Gas-Insulated Substations 1 kV to 52 kV
IEEE Std C37.123™-1996 (R2008), IEEE Guide to Specifications for Gas- Insulated, Electric Power Substation Equipment.